Phones answered 24/7Nashua, NH
Call (833) 751-2102
Serving Hillsborough County

Chimney flashing repair for Nashua roofs with older masonry

The metal where the chimney meets the roof is rebuilt into the masonry so winter water runs off instead of in.

  • Leaks, flashing and tear-offs
  • Ice dams and nor'easter snow
  • Older roofs on tight lots

Get a fast quote

Fastest: call (833) 751-2102. Or send this and we call you back.

Chimney

Chimney Flashing Repair: what it covers

Quick answer

Chimney flashing repair rebuilds the metal that seals the joint between a chimney and the roof: base flashing on the slope, counter flashing set into the masonry, and a cricket on the uphill side where the stack is wide. It is one of the most common winter leak repairs on older New Hampshire houses, because that joint moves with heat, frost and wind.

Chimney Flashing Repair illustration for Nashua, NH

Of all the joints on a pitched roof, the chimney asks the most of its flashing. Masonry expands and contracts at a different rate from metal, mortar cracks, and the sealant meant to bridge the two gives up within a few winters. In Nashua, where a chimney often rises through a roof framed a century ago, the joint is usually where the first winter stain begins.

Chimney flashing has three jobs. Base flashing ties the metal into the shingles on the downhill side. Counter flashing sits in a groove in the masonry and laps down over the base. On a wide stack, a cricket, a small peaked saddle on the uphill side, sheds water around the chimney so it does not pool against the brick. When any one of the three fails, water finds the seam and runs down the chase inside the house.

Nashua Roofing rebuilds the joint in the order it was meant to be built, which is why the repair is more than a bead of sealant. The sections below cover what to read in the masonry, why the cricket matters on a wider stack, and how the work is staged so the chimney is not left open to the weather.

Service area
Nashua & Hillsborough County
Availability
Phones answered 24/7
Warning signs

Signs you need chimney flashing repair

Working at a chimney means working near the roof edge and on masonry that may be unsound, so stay off the roof when it is wet, iced or snowed on. Do not climb the chimney itself or stand on the crown to reach the cap. Do not knock loose brick back into place with a hammer, because it can fall into the flue or into the street. Keep the area below clear while masonry is being worked, and call (833) 751-2102 for a roofer to look at the joint.

  • Water stains on the ceiling or wall where a chimney chase runs through an upper floor
  • Mortar at the crown or shoulder crumbling or missing in patches
  • Counter flashing that has pulled out of its groove or lifts when a hand is run along it
  • Sealant at the masonry split, shrunken or peeled into strips
  • Rust at the seam where the base flashing meets the chimney face
  • A dark, wet line of snow along the uphill side of the stack after a thaw
  • White crust, called efflorescence, on the brick under the roofline on one side
Job stories

Typical jobs for chimney flashing repair

Typical job
Illustration: A typical chimney flashing check on an older house

A typical chimney flashing check on an older house

What homeowners notice
A brown mark appears on the wall beside a fireplace in the upstairs room after heavy rain. The mark is small, but it returns after each storm.
What we do
The attic and the chimney base are inspected together. The counter flashing has separated from the masonry on the uphill side, and the mortar joint above it is cracked. The step flashing on the downhill side is found to be sound.
What to expect
The findings describe the separated counter flashing and the cracked joint, with photographs located against the chimney, and a written scope names the flashing replacement and the repointing as separate lines.

Options

Types and options for chimney flashing repair

Base flashing on a sloped chimney

The metal that ties the chimney into the shingle plane on the downhill and side faces. On a narrow stack it is usually the first piece to fail, and its replacement is woven into the courses rather than laid on top of them.

Counter flashing and masonry groove

The top edge of the metal set into a groove cut in the brick or stone. Where the groove has eroded or the mortar is soft, a new groove is cut or the counter flashing is re-seated, and the joint is then checked for any gap where a drip can enter.

Cricket on a wide chimney

A small peaked saddle built on the uphill side of a chimney that is wider than the roof can shed water past. Without it, snow and water pile against the masonry and find every gap. A cricket is a bigger job, because it changes the framing and the roof around it.

Skip the guesswork. Call for a straight answer.

Tell us what's happening and we'll tell you honestly whether it's a quick fix, and what chimney flashing repair should cost.

Why does the chimney leak more than the rest of the roof?

The chimney is a masonry block set into a roof that moves, and the metal around it has to move with both.

Brick and mortar expand and contract at a different rate from steel and aluminum, and each frost cycle works into every crack. The chimney also acts as a wall that catches wind-driven rain on the face it turns toward the storm, so the joint takes more water than a plain run of shingle does.

The joint is where three materials meet and two directions of movement collide, which is why it fails first. A repair that treats only the top edge, without the base or the cricket, buys one season, and then the stain comes back in the same place.

Is repointing the chimney part of the flashing repair?

Often, yes. Soft or missing mortar at the crown and shoulder lets water into the stack, and that has to be dealt with where it touches the metal.

Mortar that has eroded from the joints lets rain run into the brick, and it also loosens the grip of the counter flashing. Where the mortar is only lightly worn, repointing in a matching mix is enough. Where bricks are cracked or spalled, the crown or a section of the stack may need rebuilding first.

The masonry is usually agreed alongside the metal rather than as a separate project, because one depends on the other. A roofer who finds the crown in poor condition says so before the flashing is set, so the new metal is not fixed to a failing face.

Should the chimney cap be checked too?

Yes. A cap keeps water, leaves and animals out of the flue, and a missing or damaged one can send water down the inside of the stack.

A chimney without a cap lets rain fall straight down the flue, where it soaks the masonry and drips at the damper or the appliance. A cap that is cracked or bent is as much a source of water as an open flue, and it is inspected from the roof and, where the flue is reachable, from the top of the stack.

Any gap is noted in the written scope. The job is short, but it protects the masonry that the flashing relies on, and that is why the cap is checked on the same visit.

How far does a chimney repair reach across the roof?

The shingles on each side of the chimney are lifted and rewoven, so the repair touches several courses on every face of the stack.

Each course that runs under or over the flashing has to be relaid so water is shed in the right order, which means a repair on one side can disturb the shingles on the other. The roofer plans the lift so any change in color falls on a natural break rather than mid-slope.

Where the existing shingles are brittle they can crack when lifted, so the scope states how many courses are expected to be replaced. The homeowner knows the extent of the work before the crew is on the roof.

What if the chimney is no longer used?

An unused chimney still needs its joint sealed, because the stack and its flashing are still exposed to water and frost.

A chimney that has been capped or closed off above the roof is still a masonry block passing through the roof, and its flashing still takes the weather. A joint left unsealed lets water run down the old flue and into the house, sometimes long after the appliance has been removed.

Some owners take a chimney down entirely. That is a structural job with its own requirements, and the roof is closed over the opening in a separate sequence from the flashing work.

Our process

How our chimney flashing repair visit works

  1. Read the masonry first

    Before the metal is judged, the brick and mortar are read. Cracked joints, a failing crown or spalled brick change how the flashing can be fixed, and they are noted so new metal is not fixed to a face that is already breaking up.

  2. Follow the chase from the attic

    The chimney chase is checked in the attic and the upper rooms for staining on the brick, soft sheathing and damp framing. Water tracking down the chase often points to the flashing on one side of the stack rather than the other.

  3. Lift the courses on the uphill side

    The courses above the chimney are lifted carefully to see how the base flashing is lapped, whether a cricket exists and whether it was built to drain. Cut shingles and an old patch of tar are common finds at this point.

  4. Set the metal in order

    New base flashing is woven into the courses, with the upper piece over the shingles and the lower piece over the course beneath. Counter flashing is cut to a groove in the masonry, sealed in and bent over the base, so water runs off the metal every time it rains.

  5. Test the joint and clear the site

    The joint is checked for any lifted edge or open gap, and the crown is inspected for loose brick. Mortar dust is cleared from the gutter and roof, since it can choke a downspout and leave a clogged outlet behind.

Hillsborough County

Why chimney flashing repair is different in southern New Hampshire

Many older Nashua houses have chimneys that rise through roofs framed well over a century ago, and the stack was often built before the roof was last rebuilt. The flashing at that junction may be a patchwork of pieces from different years, and each one has to be read before it is replaced.

On the close lots near the Nashua River and in the Tree Streets, a chimney can stand within a few feet of the neighboring house. The masonry work is planned so that no mortar or debris drops onto the walks or cars next door.

Wind on the chimney side of a house is a steady factor here. A nor'easter drives rain up under the flashing on the windward face, and water finds the seam on whichever side faces the storm, so the repair checks both sides rather than only the one where the stain appears.

Related

Leak Diagnosis and Flashing Repair

The leak is traced to its real entry point, usually at flashing or an eave edge, and the metal is rebuilt in the right order.

Roof Repair

The failed section is found, scoped and rebuilt, so sound roof is left in place instead of being stripped.

Gutter and Downspout Repair

Sagging troughs, loose hangers and blocked outlets are fixed so meltwater runs away from the house rather than into it.

Storm Damage Roof Inspection

After a nor'easter or a wind event, the roof is checked for lifted courses, displaced flashing and hidden damage, and the findings are recorded in writing.

Guides

Read before you book

What the age of a Nashua house does to its roof

A City of Nashua housing study put about 60 percent of the city's homes up before 1970, and many of them carry roofs that have been patched, layered and reframed over several decades.

FAQ

Chimney Flashing Repair FAQs

Can I seal the chimney flashing myself?

A sealant bead can slow a leak for a while, but it does not fix base or counter flashing that was laid in the wrong order. A lasting repair replaces the failed metal and resets it into the courses. The safety note on this page explains why the roof itself should be left to a roofer.

How do I tell whether the leak is from the chimney or from a nearby valley?

The attic usually shows it. Water tracking down the chase or along the brick points to the chimney, while water running along a rafter toward a valley points there. A roofer follows the wet marks rather than guessing from the stain on the ceiling.

Why does the chimney leak in a thaw but not in a steady cold rain?

Thaw water carries melted snow and ice down the slope, which backs up against the uphill side of the chimney and forces its way under the metal. A steady cold rain may run off cleanly. The joint is tested against both conditions when the cause is traced.

Is a crown repair part of this job?

It can be. The crown is the sloped top of the masonry that sheds water away from the flue. A cracked crown lets water into the stack from above, so it is checked on the same visit, and the metal is not set against a failing top.

Does a chimney repair need a permit?

That is for the Nashua building department to say. The City's guidance and third-party guides differ on permits for some work, so ask the department about the specific repair. A structural change to the stack is a separate question and is asked about separately.

Should the chimney be checked after a storm?

After a heavy wind or a long wet snowfall, a quick check of the joint is sensible. Look for new staining, a counter flashing that has shifted or loose brick at the crown. The storm damage roof inspection page explains what a fuller check involves.

WhatsApp