Phones answered 24/7Nashua, NH
Call (833) 751-2102
Serving Hillsborough County

Roof leak diagnosis and flashing repair in Nashua

The leak is traced to its real entry point, usually at flashing or an eave edge, and the metal is rebuilt in the right order.

  • Leaks, flashing and tear-offs
  • Ice dams and nor'easter snow
  • Older roofs on tight lots

Get a fast quote

Fastest: call (833) 751-2102. Or send this and we call you back.

Leak Diagnosis

Leak Diagnosis and Flashing Repair: what it covers

Quick answer

Leak diagnosis finds where water actually enters a roof, which is often well away from the stain it leaves. Flashing repair rebuilds the metal at joints such as valleys, walls, chimneys and vents so water is shed in the right order. In Nashua the failures tend to appear during a thaw, when meltwater finds the weak joint.

Leak Diagnosis and Flashing Repair illustration for Nashua, NH

A stain that appears during the first warm week after a storm is rarely a new failure. It is usually a joint that has been taking water for a long time and has finally let it through, most often at flashing or at the eave where meltwater collects. The job is to find that joint rather than seal the stain, because a stain is only the place where the water came out of the wall.

Houses in Nashua make the diagnosis more involved. Flashing is seldom a single piece. It is a set of metal pieces laid into the courses at each junction, and many were fitted when the house was built or later altered with a dormer, a porch or a new vent. Older metal may be thin, and a junction repaired in the past may have been sealed rather than rebuilt, so water can travel through more than one layer before it shows.

Nashua Roofing approaches a leak as a trace, not a patch. The sections below explain how the trace is run, how flashing is rebuilt and why a bead of sealant is rarely the repair. The roof repair page covers the larger job where the covering itself has failed.

Service area
Nashua & Hillsborough County
Availability
Phones answered 24/7
Warning signs

Signs you need leak diagnosis and flashing repair

Do not climb a wet or iced roof to look at flashing, because the metal is slippery and the shingles give way underfoot. Do not pry up flashing that is still sound, since it will tear and make a new leak. Do not seal a joint while it is wet or while water is still running behind it. Catch the drip, move valuables, and call (833) 751-2102 for a roofer to trace the leak from the attic first.

  • A drip or stain that appears within a day of a thaw or after a wind-driven rain from one direction
  • Rust streaks or pitting on step flashing, counter flashing or a valley liner
  • Sealant that has cracked, shrunk or peeled away from a chimney, a wall or a vent
  • Shingle courses that run over a flashing edge in the wrong direction
  • Staining on a wall below a roof-to-wall junction, rather than under the ridge
  • Paint peeling in a narrow vertical band beside a chimney or a dormer
Job stories

Typical jobs for leak diagnosis and flashing repair

Typical job
Illustration: A typical valley leak on an older Nashua house

A typical valley leak on an older Nashua house

What homeowners notice
A stain appears on a bedroom ceiling several feet from the nearest outside wall, and it has grown after each of the last two rainfalls. The covering looks undisturbed from the street.
What we do
The roofer starts in the attic, follows the darkened decking upslope to a valley and finds the metal thin and open at a lap. The valley metal is replaced and the courses on either side are relaid into it, and the boards that were wet are photographed before the new covering goes over them.
What to expect
The findings record the stain, the attic bay that was wet and the open lap, with photographs before and after, and the homeowner is shown where the water had been traveling along the rafter.

Options

Types and options for leak diagnosis and flashing repair

Step flashing at a wall

Where a roof meets a sidewall, small metal pieces are woven into each shingle course. When they fail, the usual fix is to lift the courses, replace the pieces in order and reset the shingles above them so each one overlaps correctly.

Chimney flashing

Chimney joints combine a base flashing, a counter flashing set into the masonry and often a cricket on the uphill side. Cracked sealant at the masonry is a sign the counter flashing has lost its hold, and it is usually the first thing to check.

Valley leaks

A valley carries the water from two slopes in one channel. Leaks there usually come from a worn metal liner, a shingle cut too close to the center, or a valley that was patched rather than rebuilt when the roof was last worked on.

Vent collar and pipe boot failure

The rubber collar around a plumbing vent cracks with age and sun exposure, and water runs down the pipe into the attic. Replacing the collar is simple, but the shingles around it have to be lifted to fit it properly and keep it shedding water.

Need leak diagnosis and flashing repair today?

Call any hour and explain what is going on. You get a clear price before any work starts.

Why is the stain so far from the leak?

Water runs along the surface of boards and framing until it finds a gap, so the stain shows below the place where the water left the roof.

A joint that lets water in near the top of a slope may send it along a rafter for several feet before it drips. That is why the ceiling stain is not the place to repair. Water usually travels uphill from the stain, and the highest wet mark in the attic is a better guide than the drip itself.

Insulation slows the water and spreads it, so the drip can appear in a different room from the one where the water entered. A roofer checks the attic before the roof, because the attic often shows the path more clearly than the shingles do.

Is sealant a repair?

Sealant is a holding measure at best. It can close a small gap for a season, but it does not fix a joint that moves or was laid in the wrong order.

Caulk bonds poorly to wet or dirty metal and splits as the house flexes through temperature changes. Once a sealed joint fails, the water that sat behind the bead is trapped inside the assembly, where it rots the wood faster than the original leak did.

Flashing is a matter of lap and order: water must always run over a lower piece and never into a seam. Sealing a joint that was laid the wrong way round only hides the fault, and the repair that lasts changes the order.

How do I know which flashing has failed?

A roofer checks the metal, the shingles that overlap it and the fasteners, and looks for the place where water has run behind the metal.

Rust, pitting and gaps at a seam are the clear signs. Less obvious is a flashing that is still intact but was laid over the shingles instead of under them, which lets water in at its top edge. Lifting the courses above the flashing shows which way the metal was set.

Where the metal is old and thin, the whole run is replaced rather than one piece, because a worn sheet tends to fail at the next joint along. That judgment is made on the roof and explained before the work starts.

Can a leak come back after a repair?

It can, if the cause was not found or if the repair dealt with the surface rather than the joint.

A leak that returns is usually at a second joint that has been taking water as well, or at a point the first repair did not reach. The homeowner should treat the next long rain as the real test, and report any new stain at once rather than waiting for the ceiling to show it.

A repair is recorded with photographs, so a second leak can be compared against the first. The record also helps the next roofer, who will want to know what was laid and in what order.

What makes a leak job bigger?

The number of junctions, the age of the metal and how far water has reached into the structure set the size of the work, and each is written into the scope.

A single exposed flashing on a simple roof is a short job. Several junctions on a roof with dormers and a chimney, with wet sheathing or rot found behind the metal, is a longer one. Access also matters, since a steep slope or a tight lot changes how the work is reached and protected.

The scope is written after the trace is complete and before work begins. If rot is found, its extent is shown in the photographs and agreed before any further board is removed.

Our process

How our leak diagnosis and flashing repair visit works

  1. Interview the leak

    The homeowner's account is the first clue. When the water shows, which way the wind was blowing, whether it follows heavy rain or a thaw, and what was done to the roof recently all narrow the search before anyone climbs.

  2. Trace the stain to the attic

    In the attic, the wet insulation, the stained rafter and the nail tips are followed upslope from the stain. The roofer marks the highest point of the water path, which is the likely entry, and notes any mismatch between what the attic shows and what the ceiling shows.

  3. Test the suspect joint

    On the roof the marked junction is inspected. Flashing edges are checked for lifting, the shingles above are lifted to see how the metal is lapped, and fasteners are tested for holding. Where it is safe, a controlled water test with a helper in the attic confirms the entry point.

  4. Rebuild the flashing in order

    Failed flashing is removed and replaced in the correct sequence, with each piece lapped over the one below so water runs out rather than into the joint. Step flashing is woven between courses, and counter flashing is set into the masonry or the wall above.

  5. Confirm and document the repair

    The repaired joint is photographed, the area is marked and the homeowner is told what to watch for in the next long rain. A follow-up look is suggested if the stain was large or the ceiling stayed wet for some time.

Hillsborough County

Why leak diagnosis and flashing repair is different in southern New Hampshire

Leaks in Nashua often show up in the thaw after a storm, when meltwater works into joints that were already marginal. Because so many roofs here have flashing from more than one era, a leak at a junction may sit on the boundary between original metal and a later addition.

Along the mill district and the older streets near the Nashua River, many houses have chimneys, dormers and rear additions packed close together, so a single roof can carry a dozen junctions. That density is why a trace through the attic is worth the time before anyone opens the roof.

Wind is the usual driver of leaks in this area. Nor'easters push rain sideways under the edges of metal and shingle, so a leak can appear on a wall that faces away from the storm. A roofer weighs wind direction as well as slope when choosing which junction to check first.

Related

Roof Repair

The failed section is found, scoped and rebuilt, so sound roof is left in place instead of being stripped.

Chimney Flashing Repair

The metal where the chimney meets the roof is rebuilt into the masonry so winter water runs off instead of in.

Storm Damage Roof Inspection

After a nor'easter or a wind event, the roof is checked for lifted courses, displaced flashing and hidden damage, and the findings are recorded in writing.

Gutter and Downspout Repair

Sagging troughs, loose hangers and blocked outlets are fixed so meltwater runs away from the house rather than into it.

Guides

Read before you book

FAQ

Leak Diagnosis and Flashing Repair FAQs

Why does the water only come in when it is windy?

Wind drives rain sideways and up under the lower edge of a flashing or a shingle, where the lap is weakest. A joint that stays dry in a calm rain can leak in a driving one, which is a useful clue for the trace.

Is the chimney the usual source?

It is one of the most common, because chimney joints combine masonry, metal and sealant, and each one moves at a different rate. The chimney is checked, but so are the valleys and vent pipes that often share the same stain line on the ceiling.

Can I fix a flashing leak with roof cement?

Roof cement can hold a crack for a short time, but it is not a repair. It bonds poorly to wet metal and hides the fault. A roofer removes the failed piece and lays the flashing correctly, which is the only fix that holds.

How long before a ceiling stain shows the repair worked?

The stain may take weeks to dry and show its edge. Mark the edge in pencil and date it. If the mark grows after the next storm, the repair has not reached the entry point, and the trace should be run again.

Should I replace the whole roof if the flashing has failed?

Usually not. Flashing failure is a local fault in most cases. If the shingles are worn across the field and the flashing is failing at several places at once, a full roof becomes the better decision, as the roof replacement page explains.

Does flashing repair need a permit?

That is a question for the building department. The City's residential guidance says a re-roof of a one- or two-family home does not need a permit, while third-party guides disagree on the point, so ask the Nashua building department before the work is scheduled.

WhatsApp