This page prints no price, because no New Hampshire figure for roof replacement was verified and a number taken from elsewhere describes a different house. What it sets out is the list a roofer measures, counts and opens before a figure is written: the area, the pitch, the layers already on the deck, the boards beneath them and the way the house is reached.
Key takeaways
- Area and pitch are measured before anything else, and a roof with many planes takes more labor per square foot than a plain gable of the same size.
- The coverings already on the deck decide how much tear-off and disposal the job carries before a single new course goes down.
- Board condition cannot be judged from the street, so a sound scope carries a written allowance for whatever the tear-off uncovers.
- Valleys, chimneys, dormers and skylights each need their own metal and should be counted one by one rather than folded into a total.
- Tight Nashua lots change staging, dumpster placement and ladder access, and that setup belongs on the scope as its own line.
- Two written scopes can be compared line by line even when no figure appears on the page at all.
Why is no price printed on this page?
Because an honest local figure could not be verified, and a national average is not a Nashua price.
Roof replacement turns up in many published lists with a single average attached. Those averages come from broad surveys and lead sites, and they describe a typical house in a typical market. The housing in Nashua is not typical of either, so a reader who compares a quote with an average learns very little about whether that quote is sound.
No New Hampshire figure for this work was found in the sources checked for this page. The useful thing to do instead is to name what a roofer measures before any number is written. Read the list below before the first visit and you will know which questions show whether a scope is complete or merely short.
A scope that lists every item is easier to trust than a low figure with nothing attached to it. The sections that follow go through the items one at a time, starting with the measurements and ending with the comparison of two written scopes for the same roof.
How are the measurements taken?
A roofer counts the planes, measures the eaves and rakes and records the pitch before anything is ordered.
The first visit usually starts with the roof surface itself: the number of planes, the pitch of each one, the length of every eave and rake, and the position of every valley and hip. Many Nashua roofs were built in sections over decades, so a single rectangle rarely describes them. A rear ell can carry a pitch that differs from the main ridge, and a dormer added later can cut across a valley that the original builder never planned for.
Roof area is reported in squares, where one square is one hundred square feet of covered surface. The roofer should say whether the number came from a walk across the roof or from the ground, because a figure taken from the ground tends to miss the detail a walk finds. Ask which method was used and whether the count includes the overhangs at the eaves.
Pitch matters for both labor and safety. A steep plane needs roof jacks, a harness and more time, and a crew that has not seen the house will often understate it. Ask the roofer to record the pitch of each plane separately on the scope, so the number can be checked against the house later.
What do the layers already on the deck change?
Each covering already on the roof adds removal time, disposal and a closer look at the boards underneath.
The number of coverings on the deck is one of the first questions a careful roofer asks, and the answer is often not visible from the ground. Where a single layer of shingles is already down, a full tear-off is the usual route. Where more layers are present, removal takes longer and produces more debris, and the scope should say how the count was made and where it was taken.
City guidance on re-roofing in Nashua says that a single existing shingle layer may be roofed over provided the code is followed. Roofing over avoids the removal work, but it leaves the decking unseen and adds weight to framing that may not have been designed for a second covering. That tradeoff belongs in the written scope as an explicit choice, not hidden inside a line that says roof replaced.
Ask whether the scope assumes a tear-off or a recover. Both can be correct on the right house, but they produce different disposal, different underlayment requirements and different risks for the boards beneath. A scope that names neither approach is leaving the most important decision unmade.
How much decking might need replacing?
Soft or rotted boards are the one item nobody can see from the street, so an honest scope carries an allowance for them.
Once the old covering comes off, the decking shows what years of ice, condensation and slow leaks have done. On older Nashua houses the boards are often plank or early panel, and they can be sound in one bay and soft in the next. A roofer cannot know the count before the tear-off begins, and that is why the allowance is written into the scope rather than left to memory.
A good scope states the rate for replacement decking, the amount included before that rate applies and the rule for photographing each board that comes out. That way a change is documented rather than announced at the top of the ladder. Ask for those photographs to be included in the written findings afterward, so the homeowner keeps a record of what was found.
Soft decking near a valley or around a chimney is the most common surprise on these houses, because water concentrates at both places for years. A scope that names those two locations as likely to need an allowance shows that the roofer has looked at the house and not only at the surface of the roof.
Which details are counted one by one?
Chimneys, valleys, dormers, skylights and penetrations carry their own metal and labor, and each should appear as a separate line.
Flashing is where most replacement scopes lose their detail. A chimney needs step flashing along each side, a counter flashing set into the masonry and a cricket on the uphill side when the chimney is wide. Each of those is a separate item with its own material and labor, and each should be listed as one rather than as a general line for the chimney.
Valleys are measured by length and assessed for the metal they will carry. Skylights, plumbing stacks and exhaust vents are counted by number. A dormer adds two sidewalls and a cheek, and each of those surfaces needs its own detail where it meets the main roof. None of this is visible from the street, which is why a scope that describes only the open field of the roof leaves these items out.
Ask the roofer to read the list of penetrations back to you before the scope is signed. If the scope says flashing at the chimney and valleys without a count, ask for the count in writing. A roofer who has walked the roof will have one, and one who has not should be asked to walk it again before work begins.
What do the site and access add?
A narrow lot changes staging, dumpster placement, ladder reach and how long the crew spends before the first covering moves.
Nashua has dense blocks, and several streets were laid out long before cars. A dumpster may need a permit to sit on the road, and a truck may not fit beside a house with a short driveway. Those are logistics, but they carry labor and they belong on the scope as their own items rather than being assumed into the day rate.
Access to the roof matters as well. A two-story house with a low eave is a different job from a three-story house with a steep rear section, and a slate or tile covering is handled differently from asphalt shingle. The scope should describe the access route and the staging area, along with the square footage, so the crew's plan can be checked against the house.
Ask who will protect the landscaping, the driveway and the gutters during the work. A serious proposal names those steps and says who is responsible for them. A vague one leaves the homeowner to find the damage after the crew has gone, which is the worst time to discover it.
How do you compare two written scopes?
Compare what each scope includes and excludes, item by item, rather than looking first at the total at the bottom.
Two quotes for the same roof can differ far more in what they include than in the figure they end with. Lay the scopes side by side and check each row: measured area, layers counted, decking allowance, flashing count, disposal, underlayment, ventilation and the terms of any workmanship promise. A missing row is a question to ask, not a saving to celebrate.
Watch for silence. A scope that does not mention tear-off, disposal or protection of the property is either incomplete or leaves those items for a later change order. Neither is a good sign. Ask the roofer to add the missing lines in writing and see whether the answer is specific or general.
Scopes also show whether the roofer has seen the house. Specific notes about a particular valley, a named chimney or the rear section suggest a real visit. A generic document suggests a template, and a template does not account for an old Nashua roof with a second layer under the first and a soft bay near the chimney.
Frequently asked questions
Why does the page not give a number?
Because no verified New Hampshire figure was found, and a number taken from a national survey describes a different house in a different market. A printed figure would invite a comparison that the written scope should settle on its own terms.
Can I get a number over the phone?
Call (833) 751-2102 and describe the roof, the year it was last covered and the problem you are trying to solve. The call arranges a visit to measure the roof, and the figure follows the written scope rather than coming before it.
Does a replacement need a permit in Nashua?
The city's own guidance and third-party guides disagree, so ask the Nashua building department before work starts. Nashua roof permit rules sets out the points to raise on that call.
What should a written scope say about the boards?
It should state the decking allowance, the rate that applies beyond it, and that each board removed will be photographed and recorded before it goes to the dumpster.
This guide is general information for Hillsborough County homeowners, not a substitute for an on-site inspection. Prices are estimates. See our disclaimer.