Phones answered 24/7Nashua, NH
Call (833) 751-2102
Guide

How snow load works, and what a Nashua roof has to carry

What snow load means for a Nashua roof, the ground figure the sources give and disagree on, how collapses happen and the warning signs to act on.

Illustration for the guide "How snow load works, and what a Nashua roof has to carry" (Nashua, NH)
Short answer

Snow load is the weight a roof carries, measured in pounds per square foot of roof surface. Nashua sits in a snow region where the ground figure is roughly 50 to 60 pounds per square foot, sources differ. Collapses are rare, but they follow patterns that a homeowner can recognize early, and the first step is to stay off the roof and call for an inspection.

Key takeaways

  • Ground snow and roof snow are not the same number, and the roof figure depends on the pitch, the exposure and how the snow drifts.
  • The Nashua ground figure is given as roughly 50 to 60 pounds per square foot, and the sources disagree on the exact value.
  • Wet, heavy snow weighs far more than dry powder, so a storm that ends in rain or sleet can load a roof faster than its depth suggests.
  • A collapse usually has warning signs first: a sagging ridge, new cracks in plaster and doors that begin to bind.
  • Clearing snow from the ground to the eave lowers the load safely, while standing on the roof to shovel it is the most common way people get hurt.
  • A written inspection of the framing answers the question that a depth measurement cannot, which is whether the structure has room for the next storm.

What does snow load actually measure?

Snow load is a weight per area, the force that snow puts on each square foot of roof, and it is what the framing has to resist.

Engineers separate the snow on the ground from the snow on the roof. The ground figure is the weight of the snow that would lie on open, flat land in a given place, and it is the starting point for every roof calculation. The roof figure is then adjusted for the slope of the roof, how exposed the surface is to wind and how snow piles up against walls, parapets and other roof planes.

Snow is measured in pounds per square foot of roof surface. A foot of dry powder weighs far less than a foot of wet, compacted snow, which is why depth alone is a poor guide to risk. The water content of the snow matters more than the number on the measuring stick, and a heavy wet storm can put more load on a roof in a single day than a deeper dry one.

The question a homeowner can actually act on is whether the framing was designed for the load it is now carrying. That is a structural question, and it is answered by someone who looks at the rafters, the ceiling joists and any sag, rather than by a formula applied from the street.

What is the figure for Nashua, and why do sources differ?

The ground figure for Nashua is given as roughly 50 to 60 pounds per square foot, and the published sources do not agree on one value.

The number most often quoted for Nashua is roughly 50 to 60 pounds per square foot of ground snow, and the sources that give it disagree on the exact value. The range is the honest statement, and a single figure presented as settled would overstate what the sources support.

New Hampshire's building rules allow a federal engineering publication, ERDC/CRREL TR-02-6, to set the ground figure for a given place. That report is the reference the state accepts, so a designer or building official working in Nashua can use it to fix the value that applies to a specific roof, and that value can differ from a rough regional figure.

For a homeowner the practical point is simple. The range is the right number to keep in mind, and the exact design load for a particular roof is a matter for the framing review and the building department rather than for a website. Asking a roofer or an engineer which value was used on a given roof is a fair and specific question.

Because the figure is a range, a sensible question for any roof project is which value the design used, the upper end or a lower one. The answer belongs in the written design. A roofer or engineer who can say which value was used, and why, has taken the question seriously, and one who cannot should be asked to find out before the structure is changed.

How do snow collapses usually happen?

Collapses tend to follow a slow build-up of weight on a structure that was already weakened by age, rot, sagging or a previous leak.

The January 2011 nor'easter brought roof collapses across southern New England, a pattern that was reported widely across the region in the storm record kept by the National Oceanic and Atmospheric Administration. Storms of that kind add weight quickly, and the roofs that failed were generally those with aged framing, long spans, prior water damage or extra weight from drifting snow against a wall.

Drifts are a particular concern. Snow blown by wind builds into deep piles against a parapet, a taller wall or the side of a dormer, and the drift can carry several times the load of the snow around it. A drift that forms against a low-slope section can concentrate weight in one place where the framing was never sized for it.

Rot and water damage weaken the framing that carries the load. A rafter that has been wet for years, a ridge board that has pulled away from the end wall or a beam notched for an old chimney can each lose capacity without any visible sign from the living space. That is why an inspection of the framing is worth more than a measurement of the snow.

What warning signs should a homeowner watch for?

Sagging, new cracks, doors that stick and sounds of stress from the attic are the signs to act on the same day.

A ridge or a long run of eave that has dropped out of line is the clearest sign of a problem. Stand back from the house and look along the roofline from one end to the other, comparing the top edge with a straight line. A dip that was not there last winter should be reported at once rather than left to watch.

Cracks that open in plaster or drywall at a wall-to-ceiling joint, doors and windows that begin to stick, and a ceiling that bows downward in one area are signs that the framing is moving. Creaks and cracking sounds during a heavy snow are common on old houses, but a sound that is new or getting louder is a reason to clear the room below and call.

If any of those signs appear, keep people out of the rooms under the affected area and stay off the roof. Call (833) 751-2102 and describe what you see, including where the sag or crack is and how it has changed since the last storm. The call can arrange an inspection of the framing and, if it is needed, temporary support.

How should snow be cleared safely?

Clear from the ground, work from the lowest edge up and never work on the roof surface while it is covered with snow or ice.

Clearing snow from the ground is the safest approach. A roof rake with a long handle can pull the lowest snow off the eave and reduce the load along the bottom of the roof, where drifts tend to start. Work from the edge inward and keep the rake away from power lines and the service drop.

Shoveling the roof surface is where most injuries happen. A slope covered with snow or ice gives no footing, and a fall from a second story can be serious. Crews who clear roofs use fall protection and ground-based methods, and a homeowner should not attempt the same work from a ladder or a sloped surface.

Removing all the snow is not the goal. A thin layer left on the roof protects the covering from the worst of the freeze and thaw, and clearing too aggressively can strip the surface and leave the shingles exposed. The aim is to keep the depth and weight within the range the framing was built for.

A homeowner can make the visit more useful by clearing access to the attic hatch, moving stored items away from the rafter bays and writing down any past repair to the roof structure. A short history of the house, including any addition built after the original roof or any section of roof that has sagged before, gives the inspector a head start on the places that have already been stressed.

What does a framing inspection look at?

An inspection checks the rafters, ridge, ceiling joists and bearing walls for sag, rot, notching and any change since the house was built.

The visit starts in the attic, where the rafters and ceiling joists can be seen directly. The inspector looks for cracked or split members, boards that have bent under load, rot at the bearing points and any notch cut into a rafter for a pipe, a chimney or an old repair. The condition of the sheathing, and any water staining on it, is recorded alongside the framing.

The roof surface is considered next, with particular attention to the ridge, the valleys and any section where drifts have formed in past winters. The findings should note the pitch, the age of the covering and any sag measured against a fixed line, so that the next visit can compare against the same points.

A written report is the useful result. It should say what was found, where it was found and what, if anything, needs support or repair before the next storm. A report that only says the roof looks fine has not answered the question about the framing, and it is worth asking for the specifics in writing.

Frequently asked questions

How many inches of snow does a Nashua roof need to be worried about?

Depth is a poor guide, because wet snow weighs far more than dry snow of the same depth. The right question is whether the framing has been checked for the ground load, and whether the snow has turned heavy and wet, not how many inches have fallen.

Should I shovel the roof after every storm?

No. Clear the lowest edge from the ground, keep the eave free of ice and leave the rest unless a qualified crew with fall protection is on site. Standing on a snow-covered slope is the most common way people are hurt during winter roof work.

Can a roof collapse without warning?

Sudden failure is uncommon, but sags, cracks and sticking doors usually appear first. Treat any new sign as a reason to clear the room below and arrange an inspection rather than waiting to see whether it grows.

Is a snow-load figure printed on a roof permit?

Where a permit is needed for structural work, the design load is set as part of the review. Ask the Nashua building department which ground value applies to your address before any structural change is made.

This guide is general information for Hillsborough County homeowners, not a substitute for an on-site inspection. Prices are estimates. See our disclaimer.

Still stuck? We pick up 24/7.

If it's an emergency, call now. For non-urgent help, send the form and we'll call you back.

Keep reading

More guides

WhatsApp